Juniper-networks E-Series Instrukcja Użytkownika Strona 121
- Strona / 242
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Replacing Fan Trays
E-Series Routers
9-15
Installing the Fan Tray
To install the fan tray:
Caution: Do not use the fan tray handle to carry the fan tray assembly. Use the
handle only to push the tray into the chassis.
1 Hold the tray horizontally (ERX-14xx models) or vertically
(ERX-7xx models and ERX-310 routers) or so that the captive screws
point toward you and you can read text on the labels.
2 Place the bottom corners of the tray housing in the plastic shelf
guides of the fan tray compartment; push toward the back of the
chassis halfway, and stop.
3 Push the fan tray toward the back of the shelf until it stops.
There is an electrical connector on the back of the fan tray that pairs
with an electrical connector at the back of the shelf.
4 With an appropriate screwdriver, tighten the captive screws.
Alternate between screws when tightening them to ensure that the
electrical connectors at the back of the tray fit tightly.
5 (ERX-14xx model only) Push the top bezel back on the front of the
system.
Figure 9-9 Fan tray in ERX-7xx model
g013766
- E-Series Routers 1
- Installation and User Guide 1
- EC Declaration of Conformity 4
- SOFTWARE LICENSE AGREEMENT 5
- Contents 10
- Part 3. Appendixes 13
- About This Guide 15
- Audience 16
- Conventions 16
- Documentation 17
- Release Notes 19
- Abbreviations 19
- Web Access 19
- Contacting Customer Support 20
- Installing and Using 21
- E-Series Overview 23
- Where E-Series Routers Fit In 24
- ERX-14xx Models 26
- ERX-7xx Models 28
- ERX-310 Router 30
- E-Series Modules 32
- SRP Module 33
- Module Details 34
- SRP Module Redundancy 35
- Nonvolatile Storage 35
- SRP I/O Module 35
- Line Modules 36
- Network Management Tools 37
- Redundancy Features 38
- CHAPTER 1 40
- Unpacking and 43
- Inspecting E-Series 43
- Unpacking ERX-14xx Models 44
- Contacting Juniper Networks 45
- Installation Guidelines 47
- Environmental Requirements 48
- Regulatory Compliances 48
- Safety Guidelines 49
- Equipment Rack Requirements 50
- ERX-310 router 51
- ERX-14xx model 51
- CHAPTER 3 52
- Cabling Recommendations 54
- Installing E-Series 55
- Freestanding Installation 56
- Rack-Mounted Installation 57
- Preparing the Equipment Racks 59
- Installing Modules 61
- Slot Groups 62
- Overview 63
- OC3CE1 CE1 64
- Hot-Swapping Modules 65
- Protecting Modules and Slots 65
- Order of Installation 66
- Installing an SRP I/O Module 68
- Installing an SRP Module 68
- Removing a Module 71
- CHAPTER 5 72
- Installing the Line Modules 73
- Installing the I/O Modules 75
- Cabling E-Series 77
- CHAPTER 6 78
- Cabling E-Series Routers 78
- Cabling Overview 79
- Cabling the SRP I/O Module 81
- BNC (Europe) 82
- 26-AWG wire 82
- Wire-wrap connectors 82
- (North America, Japan) 82
- Console Ports 83
- Connecting to the Network 84
- ERX-310 router (DC model) 87
- Figure 6-6) 89
- Cabling I/O Modules 90
- HSSI Connectors 91
- RJ-45 Connectors 92
- RJ-48C Connectors 92
- LC Duplex Connectors 93
- SC Duplex Connectors 94
- SMB Connectors 94
- Cabling X.21/V.35 Connectors 95
- Powering Up E-Series 97
- Powering Up 98
- Powering Down 99
- CHAPTER 7 100
- Powering Up E-Series Routers 100
- Accessing E-Series 101
- Console Port Setup 102
- 3 Power up the system 103
- Telnet Setup 104
- The Next Step 106
- Maintaining E-Series 107
- Cleaning the System 108
- Replacing an NVS Card 111
- Checking the Memory Installed 112
- Removing SODIMMs 112
- Adding New SODIMMs 113
- Verifying the Upgrade 114
- Removing SFPs 115
- Installing SFPs 116
- 3 Hold the SFP so that: 117
- Verifying the Installation 118
- Replacing Fan Trays 119
- Removing the Fan Tray 120
- Installing the Fan Tray 121
- Perforated area 122
- Front of 122
- ERX-7xx model 122
- Troubleshooting 123
- Initialization Sequence 124
- LED Activity During Booting 125
- LED Identification 125
- • SRP module (Figure 10-1) 126
- Status LEDs 127
- CHAPTER 10 128
- Figure 10-2 FE2 module LEDs 128
- Abnormal LED Activity 129
- Redundancy Status 131
- Detecting Double-Bit Errors 133
- Fixing Double-Bit Errors 133
- System and Module 135
- Specifications 135
- System Specifications 137
- ERX-7xx Models Specifications 139
- ERX-310 Router Specifications 141
- CHAPTER 11 144
- Module Specifications 145
- functionality 146
- functionality (continued) 147
- I/O Module Specifications 160
- › 0–68.5 m (0–225 feet) 164
- › 69–137 m (226–450 feet) 164
- › min: –9.5 dBm 166
- › max: –4 dBm 166
- › min: –17 dBm 166
- › max: –3 dBm 166
- › min: –11 dBm 168
- › min: –20 dBm 168
- › min: –5.0 dBm 178
- › max: 0 dBm 178
- › min: –18 dBm 178
- › max: –0 dBm 178
- CHAPTER 12 184
- Protocol Support 185
- Channelized OCx/STMx Modules 186
- Channelized T1 and E1 Modules 187
- Channelized T3 Modules 188
- Ethernet Modules 190
- HSSI Modules 191
- OCx/STMx ATM Modules 193
- OCx/STMx POS and OC48 Modules 194
- Tunnel Service Modules 196
- Unchannelized E3 Modules 197
- Unchannelized T3 Modules 199
- X.21/V.35 Modules 201
- Appendixes 203
- Cable Pinouts 205
- CT1 and CE1 I/O Modules 208
- Installing JUNOSe 213
- Software 213
- APPENDIX B 214
- Installing JUNOSe Software 214
- Task 12: Reboot the System 219
- 1 Issue the enable command 221
- Task 9: Reboot the System 224
- Task 3: Access the Boot Mode 225
- Task 4: Assign an IP Address 226
- Task 8: Reboot the System 227
- Customer Support 231
- APPENDIX C 234
- Declaration of 235
- Conformity 235
- APPENDIX D 236
- Declaration of Conformity 236
Powiązane produkty i podręczniki dla Sprzęt komputerowy Juniper-networks E-Series
(17 strony)Samsung LN-R1550 manuals
Owner’s manuals and user’s guides for DVD players Samsung LN-R1550.
We providing pdf manuals Samsung LN-R1550 for download free by document types:
Komentarze do niniejszej Instrukcji