Juniper Networks EX2500 Instrukcja Użytkownika Strona 59
- Strona / 102
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Port Trunking Configuration Example 45
Chapter 4: Ports and Trunking
You cannot change the VLAN membership for a trunk group’s member port.
You can change the VLAN membership of the trunk group.
When an active port is configured in a trunk, the port becomes a trunk member
when you enable the trunk. The Spanning Tree parameters for the port then
change to reflect the new trunk settings.
All trunk members must be in the same Spanning Tree Group (STG) and can
belong to only one Spanning Tree Group (STG). However if all ports are tagged,
then all trunk ports can belong to multiple STGs.
When a trunk is enabled, the trunk Spanning Tree participation setting takes
precedence over that of any trunk member.
You cannot configure a trunk member as a monitor port in a port-mirroring
configuration.
Trunks cannot be monitored by a monitor port; however, trunk members can
be monitored.
A trunk member cannot be configured as a monitor port.
All ports in static trunks must be have the same link configuration (speed,
duplex, flow control).
Port Trunking Configuration Example
In the example shown in Figure 10, three ports are trunked between two switches.
Figure 10: Port Trunk Group Configuration Example
Use the following procedure to configure port trunking as shown in the Figure 10
example. You must first connect to the each switch’s command line interface (CLI)
as the administrator.
9 1011125678
SP
L/A
17 18 19 2013 14 15 16 21 22 23 24 MGMT
B
A
1234
CON RESET
EX2500
ST-A
SYS
FAN
ST-B
9 1011125678
SP
L/A
17 18 19 2013 14 15 16 21 22 23 24 MGMT
B
A
1234
CON RESET
EX2500
ST-A
SYS
FAN
ST-B
TRUNK 3: PORTS 2, 9, AND 16
TRUNK 1: PORTS 1, 11, AND 18
11
2
1
169
18
NOTE: For details about accessing and using any of the menu commands
described in this example, see the EX2500 Ethernet Switch Command Reference.
- Configuration Guide 1
- Table of Contents 3
- Part 2 Appendixes 6
- Part 3 Indexes 6
- List of Figures 7
- List of Tables 10
- About This Guide 11
- Documentation Conventions 12
- Documentation Feedback 13
- Requesting Technical Support 13
- Opening a Case with JTAC 14
- Accessing the Switch 17
- Using Telnet 19
- Using SNMP 21
- SNMPv1, SNMPv2 21
- Default Configuration 22
- User Configuration 22
- Configuring SNMP Trap Hosts 23
- Securing Access to the Switch 24
- Switch User Accounts 27
- TACACS+ Authentication 28
- Secure Shell 31
- End User Access Control 32
- User Access Control 33
- Listing Current Users 34
- Chapter 2 35
- VLAN Numbers 36
- PVID Numbers 36
- VLAN Tagging 37
- 24 VLAN Tagging 38
- VLAN Tagging 25 39
- Chapter 2: VLANs 39
- VLAN Configuration Rules 40
- Component Description 41
- Private VLANs 43
- Private VLAN Ports 43
- Spanning Tree Protocol 45
- Bridge Priority 46
- Port Priority 47
- Port Path Cost 47
- Creating a VLAN 48
- Rules for VLAN Tagged Ports 48
- Rapid Spanning Tree Protocol 49
- Port State Changes 49
- Port Type and Link Type 50
- RSTP Configuration Guidelines 50
- RSTP Configuration Example 50
- Per VLAN Rapid Spanning Tree 51
- Configuring PVRST 52
- MSTP Region 53
- Common Internal Spanning Tree 53
- MSTP Configuration Guidelines 53
- Fast Uplink Convergence 55
- Configuration Guidelines 56
- Ports and Trunking 57
- Built-In Fault Tolerance 58
- TRUNK 3: PORTS 2, 9, AND 16 59
- TRUNK 1: PORTS 1, 11, AND 18 59
- Chapter 4: Ports and Trunking 61
- Actor Switch Partner Switch 1 62
- LACP Configuration Guidelines 63
- Configuring LACP 63
- (3 seconds), instead 64
- Quality of Service 65
- Permit/Deny 66
- MAC Extended ACLs 67
- IP Standard ACLs 67
- IP Extended ACLs 68
- Understanding ACL Priority 69
- Assigning ACLs to a Port 70
- Viewing ACL Statistics 70
- ACL Configuration Examples 70
- Using ACL Filters 57 71
- Chapter 5: Quality of Service 71
- Using ACL Filters 72
- Using Storm Control Filters 73
- Broadcast Storms 73
- Configuring Storm Control 73
- Per Hop Behavior 75
- QoS Levels 76
- DSCP Mapping 76
- Priority 77
- VLAN Identifier (VID) 77
- Queuing and Scheduling 78
- Remote Monitoring 79
- RMON Group 1—Statistics 80
- RMON Group 2—History 81
- History MIB Object ID 81
- Configuring RMON History 81
- RMON Group 3—Alarms 82
- Alarm MIB Objects 82
- Configuring RMON Alarms 82
- RMON Group 9—Events 83
- 70 RMON Group 9—Events 84
- Chapter 7 85
- FastLeave 86
- IGMPv3 Snooping 87
- Static Multicast Router 88
- Detection 89
- Failure Detection Pair 90
- UFD Configuration Guidelines 90
- UFD Configuration Example 91
- Monitoring UFD 91
- 78 Monitoring UFD 92
- Appendixes 93
- 80 Appendixes 94
- Appendix A 95
- Configuring Port Mirroring 96
- Index on page 85 97
- 84 Indexes 98
- Index 85 99
- 86 Index 100
- Index 87 101
- 88 Index 102
Powiązane produkty i podręczniki dla Networking Juniper Networks EX2500
(116 strony)
Networking Juniper Networks 8 Instrukcja Użytkownika
(183 strony)
(183 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.073 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji